![]() ![]() It also has similar firmware development of other recording product line DVR K series has also introduced the GUI4.0 to ensure the series to be compatible to the newest technology available. The Turbo 4 Hybrid DVR K series has multiple models and across different platform and chipset. Due to new features and parameters constantly being added, downgrading may cause the NVR to factory default itself or require a manual default to operate properly. Refer to Step 4 and onwards in the previous section.ĭowngrading is not recommended. ![]() If upgrading from any v4.X version that was not v4.22.005, a Database Repair is recommended.Export configuration is highly recommended before performing the upgrade.Any v4.X build can be upgraded directly to v4.50.00.Upgrading from Any v4.X Build to v4.50.00. Should the problem persist, contact technical support. If you continue to observe playback issues after database repair, ensure there are no power, network, or motion detection issues.Note that while the HDD is repairing, new recordings are still being made, but some existing recordings may not be searchable until repair is complete. To verify repair progress, you may refer to the HDD status, or search the recorder log for repair started and stopped entries.For details, refer to the section "Database Optimization and Repair" above. After the upgrade is completed and the recorder is reprogrammed, it may be beneficial to perform a Database Repair.After reaching v3.4.92 and performing a full factory default, an upgrade directly to v4.50.00 is acceptable.There is a high chance of unit failure (requiring RMA) if the unit is not defaulted before upgrade. If the recorder is already at v3.4.92, a full factory default is highly recommended before upgrading to any version of v4.X.Upgrading from versions before v3.4.92 directly to any version of v4.X will likely cause the recorder to fail. All recorders must reach v3.4.92 before proceeding further.Upgrading from v3.4.92 build 170518 or Older If you are experiencing issues where playback is expected but not found, make sure "Database Repair" is performed as indicated in the procedures and scenarios below.īefore proceeding with upgrade, it is recommended that NVR configuration file is exported from the NVR over the network or on to a local USB drive. The introduction of firmware v4.0 brought about a new database architecture in order to be futureproof.Īfter upgrading to v4.X, the recorder database will need to be converted and optimized. Due to the many revisions, we recommend that the user closely follows the instructions below in order to reduce the amount of time spent as well as the chance of failure.Īs more affordable IP cameras are introduced over time with greater video resolution and data sizes, more efficient database management also becomes necessary. As such, many firmware revisions have been introduced over the years to continually ensure the product is compatible with the newest technology available. The I-series NVR (such as the DS-7716NI-I4) is one of Hikvision's most popular and feature-rich recorders. Save your Settings Note: Once this is complete, you can register the camera with a Hanwha NVR.View the most updated version of this document here: Check the appropriate user-level radio button in the Level section: Administrator – Unrestricted access to all settings.ġ0. Re-input the password in the Confirm field.ĩ. Input a password into the Password field.Ĩ. Input a username into the Username field.ħ. ![]() NOTE: The maximum number of users is 32.Ħ. Click the Add button to display the Add User window. ![]() Navigate to CONFIGURATION > NETWORK > ADVANCED SETTINGS > INTEGRATION PROTOCOL.ĥ. Access your camera by entering the IP address into your web browser.ģ. Open a Web browser (Chrome, or the browser recommended by the manufacturer.)Ģ. Is subject to change and may be out of date. NOTE : Hanwha does not communicate directly with our competitors, information in this article Applies to Models: All Hanwha SRN, HRX, QRN, XRN, PRN series NVRs Summary:Īll Hanwha NVRs and Cameras are compatible with ONVIF, which is enabled by default, allowing easy integration with any 3rd-party manufacturers, such as Hikvision brand cameras, which have ONVIF disabled by default, this article covers enabling ONVIF in this competitor's product. ![]()
0 Comments
Leave a Reply. |